|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
19-3570; Rev 0; 2/05 Low-Cost, 144MHz, Dual/Triple Op Amps with 15kV ESD Protection General Description The MAX4030E/MAX4031E unity-gain stable op amps combine high-speed performance, rail-to-rail outputs, and 15kV ESD protection. Targeted for applications where an input or an output is exposed to the outside world, such as video and communications, these devices are compliant with International ESD Standards: 15kV IEC 1000-4-2 Air-Gap Discharge, 8kV IEC 1000-4-2 Contact Discharge, and the 15kV Human Body Model. The MAX4030E/MAX4031E operate from a single 5V supply and consume only 12mA of quiescent supply current per amplifier while achieving a 144MHz -3dB bandwidth, 20MHz 0.1dB gain flatness, and a 115V/s slew rate. The MAX4031E provides individual shutdown control for each of the amplifiers. The dual MAX4030E is available in 8-pin MAX and SO packages, and the triple MAX4031E is available in 14pin TSSOP and SO packages. All devices are specified over the -40C to +85C extended temperature range. Features ESD-Protected Video Inputs and Outputs 15kV - Human Body Model 8kV - IEC 1000-4-2 Contact Discharge 15kV - IEC 1000-4-2 Air-Gap Discharge 5V Single-Supply Operation 0.1A Low-Power Shutdown Mode (MAX4031E) Input Common-Mode Range Extends to Ground 2VP-P Large-Signal -3dB BW > 50MHz Directly Drives 150 Loads Low Differential Gain/Phase: 0.2%/0.2 -40C to +85C Extended Temperature Range Compact 8-Pin MAX and 14-Pin TSSOP Packages MAX4030E/MAX4031E Applications Set-Top Boxes Standard Definition Television (SDTV) Enhanced Television (ETV) High-Definition Television (HDTV) Notebooks Projectors Security Video Systems Camcorders Digital Still Cameras Portable DVD Players PART MAX4030EEUA MAX4030EESA MAX4031EEUD MAX4031EESD Ordering Information TEMP RANGE -40C to +85C -40C to +85C -40C to +85C -40C to +85C PIN-PACKAGE 8 MAX 8 SO 14 TSSOP 14 SO Pin Configurations TOP VIEW IN_+ Typical Operating Circuit 5V 0.1F OUTA INAINA+ 1 2 3 8 VCC 7 OUTB INBINB+ SHDNA 1 SHDNC SHDNB 2 3 14 OUTC 13 INC- MAX4030E MAX4031E 75 Zo = 75 75 OUT 75 12 INC+ VCC 4 INA+ 5 INA- 6 OUTA 7 MAX4030E 6 5 MAX4031E 11 GND 10 INB+ 9 8 INBOUTB GND 4 MAX/SO 200 200 TSSOP/SO VIDEO LINE DRIVER ________________________________________________________________ Maxim Integrated Products 1 For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. Low-Cost, 144MHz, Dual/Triple Op Amps with 15kV ESD Protection MAX4030E/MAX4031E ABSOLUTE MAXIMUM RATINGS (All voltages referenced to GND, unless otherwise noted.) VCC ...........................................................................-0.3V to +6V IN_-, IN_+, OUT_, SHDN_ ..........................-0.3V to (VCC + 0.3V) Current into IN_-, IN_+, SHDN..........................................20mA Output Short-Circuit Duration to VCC or GND ............Continuous Continuous Power Dissipation (TA = +70C) 8-Pin MAX (derate 4.5mW/C above +70C) .............362mW 8-Pin SO (derate 5.9mW/C above +70C)..................471mW 14-Pin TSSOP (derate 9.1mW/C above +70C) .........727mW 14-Pin SO (derate 8.3mW/C above +70C)................667mW Operating Temperature Range ...........................-40C to +85C Junction Temperature .....................................................+150C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS (VCC = 5V, VCM = 0V, VOUT_ = VCC/2, SHDN_ = VCC, RL = to VCC/2, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1) PARAMETER Operating Supply Voltage Range Quiescent Current (per Amplifier) Shutdown Current (per Amplifier) Input Common-Mode Voltage Input Offset Voltage Input Offset Voltage Matching Input Offset Voltage Tempco Input Bias Current Input Offset Current Input Resistance Common-Mode Rejection Ratio Power-Supply Rejection Ratio Open-Loop Gain SYMBOL VCC ICC ISHDN VCM VOS VOS TCVOS IB IOS RIN CMRR PSRR AVOL GND VCM VCC - 2.25V 4.5V VCC 5.5V 0.5V VOUT_ 4.5V, RL = 2k to VCC/2 0.6V VOUT_ 4.4V, RL = 150 to VCC/2 0.4V VOUT_ 3.5V, RL = 150 to GND RL = 2k to VCC/2 Output Voltage Swing VOUT_ RL = 150 to VCC/2 RL = 150 to GND Output Short-Circuit Current SHDN_ Logic Threshold SHDN_ Logic Input Current ISC VIL VIH IIL IIH Sinking or sourcing MAX4031E MAX4031E SHDN_ = GND (MAX4031E) SHDN_ = VCC (MAX4031E) 2.0 0.10 0.10 10 10 VCC - VOH VOL - GND VCC - VOH VOL - GND VCC - VOH VOL - GND 50 50 50 40 SHDN_ = GND (MAX4031E) Guaranteed by CMRR TA = +25C TA = -40C to +85C 2.6 31 0.01 0.01 1 70 60 80 70 70 0.05 0.05 0.15 0.15 0.3 0.01 100 0.8 0.4 0.4 0.8 0.05 mA V A V dB 1 0 5 CONDITIONS Guaranteed by PSRR MIN 4.5 12 0.1 TYP MAX 5.5 22 10 VCC 2.25 13 26 UNITS V mA A V mV mV V/C A A G dB dB 2 _______________________________________________________________________________________ Low-Cost, 144MHz, Dual/Triple Op Amps with 15kV ESD Protection DC ELECTRICAL CHARACTERISTICS (continued) (VCC = 5V, VCM = 0V, VOUT_ = VCC/2, SHDN_ = VCC, RL = to VCC/2, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1) PARAMETER Disabled Output Leakage Current ESD Protection Voltage (Note 2) SYMBOL IOUT_SH CONDITIONS SHDN_ = GND (MAX4031E) Human Body Model IEC 1000-4-2 Contact Discharge IEC 1000-4-2 Air-Gap Discharge MIN TYP 0.1 15 8 15 kV MAX 10 UNITS A MAX4030E/MAX4031E AC ELECTRICAL CHARACTERISTICS (VCC = 5V, VCM = 1.5V, RL = 150 to GND, SHDN_ = VCC, AVCL_ = +2V/V, TA = +25C, unless otherwise noted.) PARAMETER Small-Signal -3dB Bandwidth Large-Signal -3dB Bandwidth Small-Signal 0.1dB Gain Flatness Large-Signal 0.1dB Gain Flatness Slew Rate Settling Time to 0.1% Channel-to-Channel Isolation Differential Phase Error Differential Gain Error Input Capacitance Capacitive-Load Stability Output Impedance Enable Time Disable Time ZOUT tON tOFF SYMBOL BWSS BWLS BW0.1dBSS BW0.1dBLS SR tS CHISO DP DG CIN No sustained oscillations f = 4.43MHz VIN_ = 1V (MAX4031E) VIN_ = 1V (MAX4031E) CONDITIONS VOUT_ = 100mVP-P, AVCL= +1V/V VOUT_ = 100mVP-P, AVCL= +2V/V VOUT_ = 2VP-P, AVCL= +1V/V VOUT_ = 2VP-P, AVCL= +2V/V VOUT_ = 100mVP-P, AVCL= +1V/V VOUT_ = 100mVP-P, AVCL= +2V/V VOUT_ = 2VP-P, AVCL= +1V/V VOUT_ = 2VP-P, AVCL= +2V/V VOUT_ = 2V step VOUT_ = 2V step f = 4.43MHz NTSC, RL = 150 to GND, AVCL = +2V/V NTSC, RL = 150 to GND, AVCL = +2V/V MIN TYP 144 53 52 40 20 10 20 9 15 40 65 0.2 0.2 8 200 2 2 0.15 MAX UNITS MHz MHz MHz MHz V/s ns dB Degrees % pF pF s s Note 1: All devices are 100% production tested at TA = +25C. Specifications over temperature limits are guaranteed by design. Note 2: ESD protection is specified for test point A and test point B only (Figure 7). _______________________________________________________________________________________ 3 Low-Cost, 144MHz, Dual/Triple Op Amps with 15kV ESD Protection MAX4030E/MAX4031E Typical Operating Characteristics (VCC = 5V, VCM = 1.5V, AVCL= +2V/V, RL= 150 to VCC/2, TA = +25C, unless otherwise noted.) SMALL-SIGNAL GAIN vs. FREQUENCY MAX4030 toc01 LARGE-SIGNAL GAIN vs. FREQUENCY 3 2 1 GAIN (dB) 0 -1 -2 -3 -4 -5 -6 VOUT = 2VP-P MAX4030 toc02 SMALL-SIGNAL GAIN FLATNESS vs. FREQUENCY 0.4 0.3 NORMALIZED GAIN (dB) 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 -0.5 VOUT = 100mVP-P MAX4030 toc03 5 4 3 2 GAIN (dB) 1 0 -1 -2 -3 -4 -5 VOUT = 100mVP-P 4 0.5 0.1 1 10 100 0.1 1 10 FREQUENCY (MHz) 100 1000 0.1 1 10 100 FREQUENCY (MHz) FREQUENCY (MHz) LARGE-SIGNAL GAIN FLATNESS vs. FREQUENCY 0.4 0.3 0.2 GAIN (dB) 0.1 0 -0.1 -0.2 -0.3 -0.4 -0.5 0.1 1 10 FREQUENCY (MHz) 100 1000 0.01 VOUT = 2VP-P MAX4030 toc04 OUTPUT IMPEDANCE vs. FREQUENCY MAX4030 toc05 DISTORTION vs. FREQUENCY -10 -20 DISTORTION (dBc) -30 -40 -50 -60 -70 3RD HARMONIC 2ND HARMONIC VOUT = 2VP-P AVCL = 2V/V MAX4030 toc06 0.5 1000 0 OUTPUT IMPEDANCE () 100 10 1 0.1 -80 -90 -100 0.1 1 10 100 0.1 1 10 100 FREQUENCY (MHz) FREQUENCY (MHz) DIFFERENTIAL GAIN (%) DIFFERENTIAL GAIN MAX4030 toc07 COMMON-MODE REJECTION vs. FREQUENCY MAX4030 toc08 POWER-SUPPLY REJECTION vs. FREQUENCY MAX4030 toc09 0.2 0.1 0 -0.1 -0.2 1st 2nd 3rd 4th 5th 6th 0 0 -20 -20 DIFFERENTIAL PHASE () DIFFERENTIAL PHASE 0.2 0.1 0 -0.1 -0.2 1st 2nd 3rd 4th 5th 6th CMR (dB) PSR (dB) -40 -40 -60 -60 -80 -80 -100 0.01 0.1 1 FREQUENCY (MHz) 10 100 -100 0.1 1 10 100 FREQUENCY (MHz) 4 _______________________________________________________________________________________ Low-Cost, 144MHz, Dual/Triple Op Amps with 15kV ESD Protection Typical Operating Characteristics (continued) (VCC = 5V, VCM = 1.5V, AVCL= +2V/V, RL= 150 to VCC/2, TA = +25C, unless otherwise noted.) MAX4030E/MAX4031E OUTPUT VOLTAGE SWING vs. RESISTIVE LOAD 0.45 0.40 0.35 VOLTAGE (V) 0.30 0.25 0.20 0.15 0.10 0.05 0 0 50 100 150 200 250 300 350 400 RESISTIVE LOAD () VCC - VOH VOL MAX4030 toc10 SMALL-SIGNAL PULSE RESPONSE MAX4030 toc11 LARGE-SIGNAL PULSE RESPONSE MAX4030 toc12 0.50 VIN 20mV/div VIN 500mV/div VOUT 50mV/div VOUT 1V/div 20ns/div 20ns/div ISOLATION RESISTANCE vs. CAPACITIVE LOAD MAX4030 toc13 CROSSTALK vs. FREQUENCY MAX4030 toc14 20 18 16 14 RISO () 12 10 8 6 4 2 0 0 100 200 300 400 0 -20 CROSSTALK (dB) -40 -60 -80 -100 500 0.1 1 10 100 CAPACITIVE LOAD (pF) FREQUENCY (MHz) _______________________________________________________________________________________ 5 Low-Cost, 144MHz, Dual/Triple Op Amps with 15kV ESD Protection MAX4030E/MAX4031E Pin Description PIN MAX4030E 1 2 3 4 5 6 7 8 -- -- -- -- -- -- MAX4031E 7 6 5 11 10 9 8 4 1 2 3 12 13 14 NAME OUTA INAINA+ GND INB+ INBOUTB VCC SHDNA SHDNC SHDNB INC+ INCOUTC Amplifier A Output Amplifier A Inverting Input Amplifier A Noninverting Input Ground Amplifier B Noninverting Input Amplifier B Inverting Input Amplifier B Output Positive Power Supply. Bypass VCC to GND with a 0.1F capacitor. Amplifier A Shutdown Input. Connect SHDNA high to enable amplifier A. Amplifier C Shutdown Input. Connect SHDNC high to enable amplifier C. Amplifier B Shutdown Input. Connect SHDNB high to enable amplifier B. Amplifier C Noninverting Input Amplifier C Inverting Input Amplifier C Output FUNCTION Detailed Description The MAX4030E/MAX4031E dual/triple, 5V operational amplifiers achieve 115V/s slew rates and 144MHz bandwidths. High 15kV ESD protection at video inputs and outputs guards against unexpected discharge. Excellent harmonic distortion and differential gain/ phase performance make these amplifiers an ideal choice for a wide variety of video and RF signal-processing applications. Applications Information Choosing Resistor Values Unity-Gain Configuration The MAX4030E/MAX4031E are internally compensated for unity gain. When configured for unity gain, a 24 resistor (RF) in series with the feedback path optimizes AC performance. This resistor improves AC response by reducing the Q of the parallel LC circuit formed by the parasitic feedback capacitance and lead inductance. Video Line Driver The MAX4030E/MAX4031E are low-power, voltagefeedback amplifiers featuring bandwidths up to 40MHz and 0.1dB gain flatness to 9MHz. They are designed to minimize differential-gain error and differential-phase error to 0.2% and 0.2, respectively. They have a 40ns settling time to 0.1%, 110V/s slew rates, and outputcurrent-drive capability of up to 50mA, making them ideal for driving video loads. Inverting and Noninverting Configurations Select the feedback (RF) and input (RG) resistor values to fit the gain requirements of the application. Large resistor values increase voltage noise and interact with the amplifier's input and PC board capacitance. This can generate undesirable poles and zeros and Ground-Sensing Inputs The MAX4030E/MAX4031E input stage can sense common-mode voltages from ground to within 2.25V of the positive supply. Rail-to-Rail Outputs The MAX4030E/MAX4031E rail-to-rail outputs can swing to within 100mV of each supply because local feedback around the output stage ensures low openloop output impedance, reducing gain sensitivity to load variations. Shutdown (MAX4031E Only) The MAX4031E offers individual shutdown control for each amplifier. Drive SHDN_ low to shut down the amplifier. In shutdown, the amplifier output impedance is high impedance. 6 _______________________________________________________________________________________ Low-Cost, 144MHz, Dual/Triple Op Amps with 15kV ESD Protection RG RF * * VOUT_ Use a PC board with at least two layers. The PC board should be as free from voids as possible. Keep signal lines as short and as straight as possible. Do not make 90 turns; round all corners. MAX4030E/MAX4031E MAX403_E IN_+ VOUT = [1+ (RF / RG)] VIN_+ RL 150 Output Capacitive Loading and Stability The MAX4030E/MAX4031E are optimized for AC performance and do not drive highly reactive loads, which decreases phase margin and can produce excessive ringing and oscillation. Figure 3 shows a circuit modification that uses an isolation resistor (RISO) to eliminate this problem. Figure 4 shows a graph of the Optimal Isolation Resistor (RISO) vs. Capacitive Load. Figure 5 shows how a capacitive load causes excessive peaking of the amplifier's frequency response if the capacitor is not isolated from the amplifier by a resistor. A small isolation resistor (usually 10 to 15) placed before the reactive load prevents ringing and oscillation. At higher capacitive loads, the interaction of the load capacitance and the isolation resistor controls the AC performance. Figure 6 shows the effect of a 10 isolation resistor on closed-loop response. Figure 1. Noninverting Gain Configuration RG IN RF VOUT_ MAX403_E VOUT = -(RF / RG) VIN RL 150 Figure 2. Inverting Gain Configuration ESD Protection As with all Maxim devices, ESD protection structures are incorporated on all pins to protect against ESD encountered during handling and assembly. Input and output pins of the MAX4030E/MAX4031E have extra protection against static electricity. Maxim's engineers have developed state-of-the-art structures enabling these pins to withstand ESD up to 15kV without damage when placed in the test circuit (Figure 7). The MAX4030E/MAX4031E are characterized for protection to the following limits: * * * 15kV using the Human Body Model 8kV using the Contact Discharge method specified in IEC 1000-4-2 15kV using the Air-Gap Discharge method specified in IEC 1000-4-2 decrease bandwidth or cause oscillations. For example, a noninverting gain-of-two configuration (RF = RG) using 2k resistors, combined with 4pF of amplifier input capacitance and 1pF of PC board capacitance, cause a pole at 79.6MHz. Since this pole is within the amplifier bandwidth, it jeopardizes stability. Reducing the 2k resistors to 100 extends the pole frequency to 1.59GHz, but could limit output swing by adding 200 in parallel with the amplifier's load resistor (Figures 1 and 2). Layout and Power-Supply Bypassing These amplifiers operate from a single 5V power supply. Bypass VCC to ground with a 0.1F capacitor as close to VCC as possible. Maxim recommends using microstrip and stripline techniques to obtain full bandwidth. To ensure that the PC board does not degrade the amplifier's performance, design it for a frequency greater than 1GHz. Pay careful attention to inputs and outputs to avoid large parasitic capacitance. Under all conditions observe the following design guidelines: * Do not use wire-wrap boards. Wire-wrap boards are too inductive. * * Do not use IC sockets. Sockets increase parasitic capacitance and inductance. Use surface mount instead of through-hole components for better high-frequency performance. RF 24 RISO MAX403_E VOUT_ CL VIN_+ Figure 3. Driving a Capacitive Load Through an Isolation Resistor _______________________________________________________________________________________ 7 Low-Cost, 144MHz, Dual/Triple Op Amps with 15kV ESD Protection MAX4030E/MAX4031E ISOLATION RESISTANCE vs. CAPACITIVE LOAD 20 18 16 14 GAIN (dB) RISO () 12 10 8 6 4 2 0 0 100 200 300 400 500 CAPACITIVE LOAD (pF) SMALL-SIGNAL GAIN vs. FREQUENCY WITH LOAD CAPACITANCE AND 10 ISOLATION RESISTOR 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 0.1 1 10 FREQUENCY (MHz) 100 1000 CL = 5pF CL = 20pF CL = 10pF Figure 4. Isolation Resistance vs. Capacitive Load Figure 6. Small-Signal Gain vs. Frequency with Load Capacitance and 10 Isolation Resistor SMALL-SIGNAL GAIN vs. FREQUENCY WITH LOAD CAPACITANCE AND NO ISOLATION RESISTOR 6 5 4 3 2 GAIN (dB) 1 0 -1 -2 -3 -4 -5 -6 0.1 1 10 FREQUENCY (MHz) 100 1000 CL = 5pF CL = 20pF CL = 10pF Figure 5. Small-Signal Gain vs. Frequency with Load Capacitance and No Isolation Resistor IEC 1000-4-2 The IEC 1000-4-2 standard covers ESD testing and performance of finished equipment; it does not specifically refer to ICs. The MAX4030E/MAX4031E enable the design of equipment that meets the highest level (level 4) of IEC 1000-4-2 without the need for additional ESD protection components. The major difference between tests done using the Human Body Model and IEC 10004-2 is higher peak current in IEC 1000-4-2. Because series resistance is lower in the IEC 1000-4-2 model, the ESD-withstand voltage measured to this standard is generally lower than that measured using the Human Body. Figure 10 shows the IEC 1000-4-2 model and Figure 11 shows the current waveform for the 8kV IEC 1000-4-2 level 4 ESD Contact Discharge test. The Air-Gap test involves approaching the device with a charged probe. The Contact Discharge method connects the probe to the device before the probe is energized. Human Body Model Figure 8 shows the Human Body Model and Figure 9 shows the current waveform it generates when discharged into low impedance. This model consists of a 150pF capacitor charged to the ESD voltage of interest, and then discharged into the test device through a 1.5k resistor. Chip Information MAX4030E TRANSISTOR COUNT: 271 MAX4031E TRANSISTOR COUNT: 387 PROCESS: BiCMOS 8 _______________________________________________________________________________________ Low-Cost, 144MHz, Dual/Triple Op Amps with 15kV ESD Protection MAX4030E/MAX4031E 5V CBYPASS 0.1F RC 50M TO 100M CHARGE CURRENT LIMIT RESISTOR RD 330 DISCHARGE RESISTANCE DEVICE UNDER TEST TEST POINT A 75 MAX403_E VEE 75 TEST POINT B HIGHVOLTAGE DC SOURCE CS 150pF STORAGE CAPACITOR 200 200 Figure 10. IEC 1000-4-2 ESD Test Model Figure 7. ESD Test Circuit I 100% RC = 1M CHARGE CURRENT LIMIT RESISTOR CS = 150pF RD = 1.5k DISCHARGE RESISTANCE STORAGE CAPACITOR 90% I PEAK DEVICE UNDER TEST HIGHVOLTAGE DC SOURCE 10% t r = 0.7ns TO 1ns t 30ns 60ns Figure 8. Human Body ESD Model Figure 11. IEC 1000-4-2 ESD Generator Current Waveform IP 100% 90% AMPERES 36.8% 10% 0 0 tRL TIME tDL CURRENT WAVEFORM Ir PEAK-TO-PEAK RINGING (NOT DRAWN TO SCALE) Figure 9. Human Body Current Waveform _______________________________________________________________________________________ 9 Low-Cost, 144MHz, Dual/Triple Op Amps with 15kV ESD Protection MAX4030E/MAX4031E Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) 8LUMAXD.EPS 8 4X S 8 INCHES DIM A A1 A2 b c D e E H MIN 0.002 0.030 MAX 0.043 0.006 0.037 MILLIMETERS MAX MIN 0.05 0.75 1.10 0.15 0.95 y 0.500.1 0.60.1 E H 1 0.60.1 1 D L S BOTTOM VIEW 0.014 0.010 0.007 0.005 0.120 0.116 0.0256 BSC 0.120 0.116 0.198 0.188 0.026 0.016 6 0 0.0207 BSC 0.25 0.36 0.13 0.18 2.95 3.05 0.65 BSC 2.95 3.05 4.78 5.03 0.41 0.66 0 6 0.5250 BSC TOP VIEW A2 A1 A e c b L SIDE VIEW FRONT VIEW PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE, 8L uMAX/uSOP APPROVAL DOCUMENT CONTROL NO. REV. 21-0036 J 1 1 10 ______________________________________________________________________________________ Low-Cost, 144MHz, Dual/Triple Op Amps with 15kV ESD Protection Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) MAX4030E/MAX4031E ______________________________________________________________________________________ TSSOP4.40mm.EPS 11 Low-Cost, 144MHz, Dual/Triple Op Amps with 15kV ESD Protection MAX4030E/MAX4031E Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) INCHES DIM A A1 B C e E H L MAX MIN 0.069 0.053 0.010 0.004 0.014 0.019 0.007 0.010 0.050 BSC 0.150 0.157 0.228 0.244 0.016 0.050 MILLIMETERS MAX MIN 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 1.27 BSC 3.80 4.00 5.80 6.20 0.40 1.27 N E H VARIATIONS: 1 INCHES MILLIMETERS MIN 4.80 8.55 9.80 MAX 5.00 8.75 10.00 N MS012 8 AA 14 AB 16 AC TOP VIEW DIM D D D MIN 0.189 0.337 0.386 MAX 0.197 0.344 0.394 D A e B A1 L C 0-8 FRONT VIEW SIDE VIEW PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE, .150" SOIC APPROVAL DOCUMENT CONTROL NO. REV. 21-0041 B 1 1 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2005 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc. SOICN .EPS |
Price & Availability of MAX4030E |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |